Finds moisture behind panels and in the decking without tearing the roof apart. We use it on every diagnostic to confirm the leak source before we start work.
Metal Roof Repair Wilkes-Barre PA done right the first time
Metal Roof Repair Wilkes-Barre PA means finding the leak, sealing it, and making sure it stays sealed through another Pennsylvania winter. We handle standing seam, corrugated, and exposed-fastener metal roofs on homes and commercial buildings across Luzerne County.
Serving Wilkes-Barre and nearby areas.
How big is the metal roof job?
Section repair
Multiple leak points, flashing work, or a panel section that needs replacement.
- 1. Small repair One or two failing seams or fasteners, sealed and water-tested the same visit.
- 2. Section repair Multiple leak points, flashing work, or a panel section that needs replacement.
- 3. Full scope Widespread rust, storm damage, or decking rot. Planned in writing first.
Drag the needle to compareTouch and drag the needle
- 30Services from one local team
- 20Areas served around Wilkes-Barre
- Camera firstWe trace the leak before we seal it
- Water testWe confirm the repair before we leave
What our metal roof repair includes
Every metal roof repair job includes a full diagnostic, the repair itself, and a water test to confirm the leak is stopped.
Work order
Metal Roof Repair- Full leak diagnostic: We walk the roof with a moisture meter and infrared thermal camera, checking seams, fasteners, flashing, and penetrations. Every suspect area gets photographed so you can see what we found.
- Seam and fastener repair: We reseal failed seams with metal-compatible sealant and replace backed-out fasteners with neoprene-washered screws. This is the most common metal roof repair and covers most leaks.
- Flashing repair: Chimney, skylight, and vent flashing get repaired or replaced as needed. We use metal flashing that matches the roof and seal it with the right sealant for the material.
- Rust treatment: Rusted areas get treated with a converter primer before sealing, so the repair does not fail at the same edge next season. Severe rust may require panel replacement.
- Water test and photos: After the repair, we run water over the area and check inside for moisture. You get before-and-after photos and a written summary of what was done.
What the first metal roof visit covers
First visit
We walk the roof, trace the leak, photograph the findings, and explain what the repair involves.
Metal roof repair at homes
We repair metal roofs on houses across Wilkes-Barre and Luzerne County.
Leaking seams
Resealed with metal-compatible sealant
Backed-out fasteners
Replaced with neoprene-washered screws
Chimney flashing
Repaired or replaced and water-tested
Storm-lifted panels
Re-secured or replaced with matching panels
Metal roof repair at businesses
We work on commercial metal roofs with minimal disruption to your tenants and operations.
Flat metal roofs
Seams, drains, and penetrations repaired
Membrane transitions
EPDM and TPO edges resealed
Vent penetrations
Flashing repaired above tenant spaces
What Metal Roof Repair Wilkes-Barre PA actually involves
A metal roof that is repaired properly lasts for years. A patch that fails next season costs more in water damage than the repair itself. We do the job once, and we test it before we leave.
Metal Roof Repair Wilkes-Barre PA is the process of locating and correcting failures in metal roofing systems, including standing seam panels, corrugated panels, and exposed-fastener roofs. The work covers seam resealing, fastener replacement with neoprene washers, flashing repair, panel re-securing, and rust treatment. We use a moisture meter and infrared thermal camera to trace water back to its entry point, because on metal roofs the leak is rarely directly above the stain on your ceiling.
Most metal roof failures we see in Wilkes-Barre come from three things: thermal movement that opens seams, fastener back-out from freeze-thaw cycles, and rust along cut edges. Older homes in Parsons and Miners Mills often have original corrugated panels that have been patched several times. If you need metal roof repair near me Wilkes-Barre PA, we can usually tell you within an hour whether the panel is repairable or whether a section needs replacement.
- What it is
- Sealing and repairing failed seams, fasteners, and flashing on metal roofs.
- When it helps
- When a metal roof leaks, rusts, or loses panels to wind and storms.
- What you get
- A watertight repair, photos of the work, and a written summary.
How our metal roof repair process works
From the first call to the final walkthrough, here is exactly what happens when you book metal roof repair with us in Wilkes-Barre.
Tools and methods we use
Each method answers a different question. Together they leave very little to guess.
Confirms the thermal camera findings by measuring actual moisture content in the decking and insulation. This tells us how far the water has spread.
Used for re-securing panels and installing new fasteners. On metal roofs, we use screw guns with depth-setting noses to avoid over-driving fasteners.
Applies metal-compatible sealant to seams, flashing, and fasteners. We use sealants rated for metal roof expansion and contraction.
Gets us safely onto the roof and keeps us anchored while we work. Every technician on a roof wears a harness, no exceptions.
When to call for metal roof repair
You notice a water stain on the ceiling after a heavy rain and your home has a metal roof.
We inspect the roof with a moisture meter and thermal camera to trace the leak to its source, then repair the failed…
HomesA storm lifted several panels on your standing seam roof and rain is getting in.
We tarp the affected section the same day to stop water intrusion, then return with matching panels within 48 hours to do…
HomesYour commercial building has a metal roof leaking at a vent or penetration above a tenant space.
We diagnose the leak, repair the penetration flashing, and reseal the joint. Work is scheduled to minimize disruption to your tenants.
BusinessesYou are buying a home in Wilkes-Barre with a metal roof and want to know its condition before closing.
We inspect the full metal roof system, check seams, fasteners, flashing, and decking, and give you a written report with photos and…
Homes
How metal roof repair works in Wilkes-Barre
Wilkes-Barre metal roofs take a beating. Freeze-thaw cycles from October through April open seams and back out fasteners. Summer heat expands panels, and the next cold snap contracts them. That movement is what causes most of the leaks we fix.
Parsons
Older housing stock with original corrugated metal panels. Many roofs here have been patched multiple times and need fastener replacement and seam resealing.
Downtown Wilkes-Barre
Commercial buildings with flat metal and membrane roofs. Leaks here usually show up at seams, drains, and penetrations above tenant spaces.
Miners Mills
Mix of older homes and small commercial buildings. Metal roofs here take heavy wind exposure and need regular fastener checks after storms.
- Parsons
- Downtown Wilkes-Barre
- Miners Mills
- Heights
- Iron Triangle
From problem to finished result.
Slide to compare the photo with an illustrative inspection view. It is generated from the photo, not a measurement.
PhotoStanding seam leak at chimney flashing
Before: A homeowner in the Heights had a ceiling stain that grew every time it rained. Three contractors told them the metal roof needed full replacement. The actual problem was rusted chimney flashing and two failed seams.
After: We replaced the flashing, resealed the seams, and replaced eight fasteners. The ceiling stain dried out and has not returned through two winters.
Wind-lifted panels in Parsons
Before: A storm lifted four standing seam panels on a Parsons home. Rain was pouring into the attic. The homeowner called us at 6 a.m. and we had a tarp on the roof by 9 a.m.
After: We tarped the same morning and returned two days later with matching panels. The repair matched the original seam spacing exactly.
Commercial roof leak above tenant space
Before: A Downtown Wilkes-Barre property manager had a metal roof leaking at a vent penetration above a retail tenant. The leak had stained ceiling tiles and was getting worse.
After: We diagnosed it with a thermal camera, repaired the vent flashing, and resealed the penetration. The work was done in one day with no disruption to the tenant.
Metal roof problems we fix in Wilkes-Barre
Metal roofs fail in predictable ways. Here are the problems we see most often in Wilkes-Barre and how we fix them.
Leaking at seams and fasteners
Water gets under the panels, soaks the decking, and shows up as ceiling stains or attic mold. Left alone, it rots the plywood and insulation.
Rusted panels and cut edges
Rust eats through the panel from the edge inward. Once it perforates, water runs straight through and the panel needs replacement.
Wind-lifted or missing panels
A lifted panel lets wind-driven rain straight into the roof assembly. In a storm, a missing panel can expose the entire attic in minutes.
Leaking chimney and skylight flashing
Failed flashing sends water down the chimney or around the skylight frame, damaging ceilings and walls.
Why metal roof repair beats replacement
A targeted repair on a metal roof costs a fraction of a full replacement and can add years of service life when the panels themselves are…
Stop leaks fast
A metal roof leak repair Wilkes-Barre PA call typically takes two to four hours on site.
Extend panel life
Replacing 12 to 20 fasteners and resealing three or four seams can add eight to twelve years to a metal roof that is otherwise…
Match existing panels
When a panel is too far gone, we source matching gauge and profile metal roofing panels so the repair blends with the original roof.
Protect the deck
Water that gets past a metal roof soaks plywood decking and insulation. Catching it early keeps roof deck rot from spreading.
Metal roof repair cost in Wilkes-Barre
A simple fastener and sealant repair sits at the low end. Standing seam panel replacement, multiple leak points, or difficult access push toward the higher end.
Included
Quoted after a first look
- Full leak diagnostic
- Seam and fastener repair
- Flashing repair
- Rust treatment
What changes the scope
Quoted after a first look
- Number of leak points
- Panel type and access
- Rust and panel damage
- Flashing and penetration work
What you receive on a metal roof repair
Clear records you can keep and share.
Inspection photos
Every suspect area documented before work starts
Repair summary
What was sealed, replaced, or treated
Water test record
Confirmation the leak is stopped
Local metal roof repair experience
We work on metal roofs every week in Wilkes-Barre and across Luzerne County.
Moisture readings
We measure moisture content in the decking to see how far water has spread.
Thermal images
Temperature differences reveal moisture behind panels without tearing the roof apart.
Fastener condition
We check for backed-out or rusted fasteners and note how many need replacement.
Is your Wilkes-Barre neighborhood covered?
Type your ZIP code or town. If you do not see yours, call and ask.
Wilkes-Barre ZIP codes
- 18702
- 18701
- 18705
- 18703
- 18710
- 18711
- 18762
- 18765
- 18766
- 18767
- 18769
- 18773
Towns we serve.
Based in Wilkes-Barre and covering the places around it. Pick one for local details.
What Wilkes-Barre homeowners say
Our metal roof was leaking at the chimney flashing for two winters. Three other companies just wanted to sell us a whole new roof. These guys found the actual leak, replaced the rusted flashing, and resealed it. Dry attic ever since.
A windstorm lifted two panels on our standing seam roof. They came out the same afternoon, tarped it, and came back two days later with matching panels. You cannot tell where the repair is. The price was exactly what they quoted on the first visit.
We manage a commercial building with a metal roof that was leaking at a vent penetration. They diagnosed it with a thermal camera, showed us the photos, and had it sealed the same day. No disruption to our tenants. We use them for all our roof work now.
Frequently Asked Questions
Short answers for the first few minutes. The team can cover the rest.
Still have a question?
Describe what you are seeing and we will point you to the right next step.
(570) 481-9079A simple fastener and sealant repair on a small section sits at the low end. Standing seam panel replacement or multiple leak points push toward the higher end. We give you a firm price after the on-roof inspection, before any work starts.
We do. Wilkes-Barre Roof Repair Pros handles metal roofing repair near me Wilkes-Barre Pennsylvania calls across Luzerne County, including Downtown, Parsons, Miners Mills, and the Heights. We work on standing seam, corrugated, and exposed-fastener metal roofs. Call (570) 481-9079 and we will get a technician to your address, usually the same day.
In most cases, yes. Metal Roof Repair in Wilkes-Barre PA same day is our standard for active leaks. We keep tarp material and common fasteners on the truck. If the repair needs a matching panel that we do not have on hand, we tarp the area today and return with the panel within 48 hours.
We trace the leak with a moisture meter and infrared thermal camera, then repair the actual entry point, not just the stain on your ceiling. That usually means resealing seams, replacing fasteners with neoprene washers, repairing flashing, and treating rust. After the repair, we water-test the area and check inside to confirm it is dry.
Related Services
Other services from the same team.
Get Metal Roof Repair Wilkes-Barre PA today
(570) 481-9079One call gets a technician on your roof, usually the same day. Call (570) 481-9079 and we will stop the leak and give you a straight price on the repair.
Contact Wilkes-Barre Roof Repair Pros
Call us any time for Emergency Roof Repair Wilkes-Barre PA. We answer the phone day and night, and we give you a real arrival window. If you prefer, send an email with photos of the damage and we will get back to you fast. We serve all of Wilkes-Barre and Luzerne County.